First setup
- Set the water hardness and install the correct filter if supplied.
- Fill with fresh water and dry, uncoated beans.
- Complete the first-use rinse and prime sequence.
- Set a moderate strength and volume before personalising drinks.
Coffee Index
Independent owner support · Australia
E8
user guide.
JURA
Setup, everyday use, cleaning and safe troubleshooting matched to this automatic machine.
Owner routine
From first setup
to prompted care.
Daily use
- Fill with fresh water and check the bean hopper.
- Let startup rinsing finish.
- Choose the saved drink and adjust strength before volume.
- Empty the tray or grounds drawer when prompted rather than on a fixed guess.
After each use
- Run the milk rinse immediately.
- Refrigerate or empty the milk container as its manual directs.
- Empty the drip tray and grounds or capsule container when needed.
Weekly care
- Wash removable trays, baskets, carafes and containers with the method allowed by the manual.
- Clean accessible coffee oils from the outlet or group.
- Brush the dry, accessible grinder chute; never add water to the grinder.
- Inspect removable seals and the power lead for visible damage.
When prompted
- Run cleaning and descaling programs only with the product and sequence approved for the exact model.
- Set water hardness correctly so prompts reflect local water conditions.
- Replace water filters and user-serviceable seals at the specified interval.
- Record error codes or light patterns before contacting support.
Problem library
9 common symptoms.
Safe checks first.
Work through the steps in order. A maintenance label means cleaning or a user-serviceable check may be due. Authorised-service labels mark problems where continued use can be unsafe.
01Machine will not turn onquick check+
No lights, display or response from the controls.
- Power point, plug or lead issue
- Machine power switch or standby state
- Protection mode after overheating
- Switch the machine off and unplug it.
- Check the lead and plug for visible damage. Do not use the machine if either is damaged.
- Test the wall outlet with another low-risk appliance and avoid overloaded power boards.
- Let the machine cool for at least 30 minutes, then reconnect it directly to the wall outlet.
- Follow the official manual's power-on or standby sequence.
02No water or very little watermaintenance+
The pump runs but little or no water reaches the cup.
- Empty or incorrectly seated tank
- Air trapped after the tank ran dry
- Scale or coffee residue restricting flow
- Outlet, shower screen or filter is blocked
- Switch off and let the machine cool before removing parts.
- Fill the tank with fresh water and seat it firmly, checking any tank valve moves freely.
- Remove coffee, capsule or portafilter and try the manufacturer's plain-water or rinse cycle.
- Clean only the removable outlet parts identified in the official manual.
- If the machine has a priming procedure, follow the exact model instructions.
- If flow remains restricted, run the manufacturer-approved descale program only when the manual says it is appropriate.
03Coffee is not hot enoughquick check+
The drink is cooler than expected or loses heat quickly.
- Cup and brew path are cold
- Machine has not fully preheated
- Large cold milk volume
- Scale affecting heat transfer
- Temperature setting changed
- Allow the complete preheat or ready sequence to finish.
- Warm the cup with hot water and discard it before brewing.
- Run the official blank rinse if the manual recommends one.
- Check the saved temperature setting where available.
- Use the prompted descale program if it is due; do not improvise a descaling recipe.
04Water is leakingauthorised service+
Water appears under, behind or around the machine.
Stop using the machine if electrical safety is uncertain.
Do not restart a machine with smoke, burning smells, sparking, a damaged lead or water near electrical parts.
- Tank or drip tray is overfilled or incorrectly seated
- Removable seal or connection is dirty
- Internal hose, valve or boiler leak
- Switch off at the controls, then at the wall, and unplug if it is safe to do so.
- Let the machine cool and dry the bench completely.
- Inspect and reseat only the removable tank, drip tray and external accessories.
- Check whether the water returns with a plain-water cycle while you remain beside the machine.
- If water appears from the body, near the lead, or beneath the machine again, stop using it and arrange authorised service.
05Unusual noise, burning smell or smokeauthorised service+
The machine sounds mechanically abnormal or produces an electrical or burning smell.
Stop using the machine if electrical safety is uncertain.
Do not restart a machine with smoke, burning smells, sparking, a damaged lead or water near electrical parts.
- Foreign material or jam
- Pump running dry
- Motor, heater or electrical fault
- Internal leak reaching electrical components
- Stop the cycle immediately.
- Switch off at the machine and wall outlet. Unplug only if it is safe to approach.
- Do not restart, open the casing or pour water into the machine.
- Check Product Safety Australia for a recall and contact the manufacturer or an authorised service agent with the model and serial number.
06Coffee is weak or wateryquick check+
Automatic drinks have little body even at stronger settings.
- Strength or aroma setting is low
- Grind is too coarse
- Beans are stale or unusually oily
- Brew unit or coffee path needs cleaning
- Increase the saved strength or reduce the programmed water volume.
- Use fresh, dry, uncoated beans.
- If the manual permits grinder adjustment, move one step finer only while the grinder is operating.
- Rinse the removable brew unit only where the manual says it is user-removable, then let it dry fully.
- Run the prompted coffee-path cleaning cycle.
07Brew unit or grounds drawer messagemaintenance+
A tray, drawer or brew-unit warning remains after refitting.
- Machine was switched off in the wrong position
- Tray or grounds container was refitted too quickly
- Brew unit is not in its home position
- Sensor area is dirty
- Use the machine's normal power button and allow the shutdown cycle to finish.
- Remove, empty and dry the drip tray and grounds container.
- Wait at least 10 seconds before refitting so the machine can register removal.
- Remove or refit the brew unit only in the state and position described by the official manual.
- Do not force the brew unit or reach inside the drive mechanism.
08Built-in grinder is jammed or inconsistentmaintenance+
The grinder is noisy, stalls, produces little coffee or the dose changes unexpectedly.
- Oily, flavoured or foreign material in the hopper
- Burr setting changed while stationary
- Chute is blocked
- Hopper is not locked
- Burrs are worn or damaged
- Stop grinding and switch the machine off.
- Remove beans only as the manual allows; never put water into the grinder.
- Check the hopper lock and clear the accessible chute with the supplied dry brush.
- For machines that require it, make grind changes only while the burrs are running.
- Restart with a small amount of dry, uncoated beans.
- If the grinder knocks, stalls or smells hot, stop and arrange service.
09Milk is not frothing or sputtersmaintenance+
The milk drink is flat, bubbly, intermittent or mostly steam.
- Milk path contains residue
- Air intake is blocked
- Carafe or tube is not seated
- Milk is too warm or unsuitable for the selected setting
- Refrigerate the milk and use a clean container.
- Run the milk-system rinse immediately after use.
- Disassemble only the removable carafe, tube and air-intake parts shown in the manual.
- Wash or soak them using the manufacturer-approved method and rinse thoroughly.
- Refit every seal and connector, then test with cold milk.
STILL NOT FIXED?
Use the exact manual or authorised support.
Record the model, serial number, warning message or light pattern, what happened immediately before the fault and the checks already completed.
Visit official JURA support ↗