Australian
Coffee Index
Home›Machines›Breville the Infuser›User guide

Independent owner support · Australia

the Infuser
user guide.

Breville

Setup, everyday use, cleaning and safe troubleshooting matched to this manual espresso machine.

Troubleshoot a problem ↓View machine profile →
Breville the Infuser manual espresso editorial illustration

Owner routine

From first setup
to prompted care.

01

First setup

  1. Wash the tank, basket and portafilter.
  2. Set water hardness where supported and run the first-use flush.
  3. Pair the machine with an espresso-capable grinder.
  4. Warm the group, portafilter and cup before dialling in.
02

Daily use

  1. Allow full preheat and run the recommended blank flush.
  2. Grind, dose, distribute and tamp consistently.
  3. Brew to a measured beverage mass.
  4. Purge, texture milk, then wipe and purge the wand immediately.
03

After each use

  1. Wipe and purge the steam wand immediately.
  2. Knock out the puck and rinse the basket and portafilter.
  3. Empty standing water from the drip tray.
04

Weekly care

  1. Wash removable trays, baskets, carafes and containers with the method allowed by the manual.
  2. Clean accessible coffee oils from the outlet or group.
  3. Clean the separate grinder according to its own manual.
  4. Inspect removable seals and the power lead for visible damage.
05

When prompted

  1. Run cleaning and descaling programs only with the product and sequence approved for the exact model.
  2. Set water hardness correctly so prompts reflect local water conditions.
  3. Replace water filters and user-serviceable seals at the specified interval.
  4. Record error codes or light patterns before contacting support.

Problem library

10 common symptoms.
Safe checks first.

Work through the steps in order. A maintenance label means cleaning or a user-serviceable check may be due. Authorised-service labels mark problems where continued use can be unsafe.

01Machine will not turn onquick check+

No lights, display or response from the controls.

LIKELY CAUSES
  • Power point, plug or lead issue
  • Machine power switch or standby state
  • Protection mode after overheating
SAFE CHECKS · IN ORDER
  1. Switch the machine off and unplug it.
  2. Check the lead and plug for visible damage. Do not use the machine if either is damaged.
  3. Test the wall outlet with another low-risk appliance and avoid overloaded power boards.
  4. Let the machine cool for at least 30 minutes, then reconnect it directly to the wall outlet.
  5. Follow the official manual's power-on or standby sequence.
SUCCESS CHECK

The machine powers on normally without heat, smell, sparking or repeated shutdown.

02No water or very little watermaintenance+

The pump runs but little or no water reaches the cup.

LIKELY CAUSES
  • Empty or incorrectly seated tank
  • Air trapped after the tank ran dry
  • Scale or coffee residue restricting flow
  • Outlet, shower screen or filter is blocked
SAFE CHECKS · IN ORDER
  1. Switch off and let the machine cool before removing parts.
  2. Fill the tank with fresh water and seat it firmly, checking any tank valve moves freely.
  3. Remove coffee, capsule or portafilter and try the manufacturer's plain-water or rinse cycle.
  4. Clean only the removable outlet parts identified in the official manual.
  5. If the machine has a priming procedure, follow the exact model instructions.
  6. If flow remains restricted, run the manufacturer-approved descale program only when the manual says it is appropriate.
SUCCESS CHECK

A plain-water cycle runs evenly, without unusual pump noise or leakage.

03Coffee is not hot enoughquick check+

The drink is cooler than expected or loses heat quickly.

LIKELY CAUSES
  • Cup and brew path are cold
  • Machine has not fully preheated
  • Large cold milk volume
  • Scale affecting heat transfer
  • Temperature setting changed
SAFE CHECKS · IN ORDER
  1. Allow the complete preheat or ready sequence to finish.
  2. Warm the cup with hot water and discard it before brewing.
  3. Run the official blank rinse if the manual recommends one.
  4. Check the saved temperature setting where available.
  5. Use the prompted descale program if it is due; do not improvise a descaling recipe.
SUCCESS CHECK

The machine reaches its normal ready state and repeat drinks are consistently hotter.

04Water is leakingauthorised service+

Water appears under, behind or around the machine.

Stop using the machine if electrical safety is uncertain.

Do not restart a machine with smoke, burning smells, sparking, a damaged lead or water near electrical parts.

LIKELY CAUSES
  • Tank or drip tray is overfilled or incorrectly seated
  • Removable seal or connection is dirty
  • Internal hose, valve or boiler leak
SAFE CHECKS · IN ORDER
  1. Switch off at the controls, then at the wall, and unplug if it is safe to do so.
  2. Let the machine cool and dry the bench completely.
  3. Inspect and reseat only the removable tank, drip tray and external accessories.
  4. Check whether the water returns with a plain-water cycle while you remain beside the machine.
  5. If water appears from the body, near the lead, or beneath the machine again, stop using it and arrange authorised service.
SUCCESS CHECK

No water returns after the removable parts are correctly seated. Any internal or electrical-area leak requires service.

05Unusual noise, burning smell or smokeauthorised service+

The machine sounds mechanically abnormal or produces an electrical or burning smell.

Stop using the machine if electrical safety is uncertain.

Do not restart a machine with smoke, burning smells, sparking, a damaged lead or water near electrical parts.

LIKELY CAUSES
  • Foreign material or jam
  • Pump running dry
  • Motor, heater or electrical fault
  • Internal leak reaching electrical components
SAFE CHECKS · IN ORDER
  1. Stop the cycle immediately.
  2. Switch off at the machine and wall outlet. Unplug only if it is safe to approach.
  3. Do not restart, open the casing or pour water into the machine.
  4. Check Product Safety Australia for a recall and contact the manufacturer or an authorised service agent with the model and serial number.
SUCCESS CHECK

Do not use the machine again until the manufacturer or an authorised technician confirms it is safe.

06Espresso runs slowly or only dripsquick check+

The pump sounds active but the espresso barely flows.

LIKELY CAUSES
  • Grind is too fine
  • Dose is too large
  • Puck is tamped or compressed too firmly
  • Basket or shower screen is blocked
  • Scale is restricting the water path
SAFE CHECKS · IN ORDER
  1. Stop the shot rather than letting the pump strain for a long period.
  2. Clean the basket holes and group outlet using only the tools described in the manual.
  3. Try a slightly coarser grind and reduce the dose enough to avoid the puck touching the shower screen.
  4. Tamp level and consistently rather than with extreme force.
  5. Run the official cleaning or descale program if it is due.
SUCCESS CHECK

The shot begins within the machine's normal range and flows in a steady, continuous stream.

07Espresso runs fast or tastes weakquick check+

The shot gushes, looks pale or lacks body.

LIKELY CAUSES
  • Grind is too coarse
  • Dose is too small
  • Coffee is stale
  • Channelled or uneven puck
  • Pressurised and non-pressurised baskets are being confused
SAFE CHECKS · IN ORDER
  1. Use fresh coffee appropriate for espresso.
  2. Confirm the correct basket for the coffee and workflow.
  3. Adjust the grinder one controlled step finer.
  4. Distribute the grounds evenly and tamp level.
  5. Change one variable at a time and compare the next shot.
SUCCESS CHECK

The flow slows, colour stays richer for longer and the drink tastes more balanced.

08Espresso tastes sour or bitterquick check+

The machine works, but the cup is sharply sour, hollow, harsh or drying.

LIKELY CAUSES
  • Sour: under-extraction from coarse grind, short contact or low heat
  • Bitter: over-extraction from fine grind, long contact or overheated coffee
  • Old coffee oils or scale
  • Unsuitable water or stale beans
SAFE CHECKS · IN ORDER
  1. Start with freshly roasted beans and fresh water.
  2. For sour coffee, move slightly finer or extend the yield; for bitter coffee, move slightly coarser or shorten it.
  3. Keep dose and beverage mass consistent while changing only one variable.
  4. Clean the basket, group outlet and grinder path as the manuals direct.
  5. Confirm the machine is fully preheated and the descale prompt is not overdue.
SUCCESS CHECK

Several repeat shots taste balanced without needing extreme grind or temperature settings.

09Water leaks around the portafiltermaintenance+

Water escapes around the group during brewing.

LIKELY CAUSES
  • Portafilter is not fully locked
  • Basket rim or group seal has coffee on it
  • Basket is overfilled
  • Group seal is worn or damaged
SAFE CHECKS · IN ORDER
  1. Stop the shot and allow the group to depressurise before removing the portafilter.
  2. Clean and dry the basket rim and group sealing surface.
  3. Reduce the dose if the puck contacts the shower screen.
  4. Lock the portafilter in using normal hand pressure—do not force it beyond its designed position.
  5. If leakage continues with a clean, correctly filled basket, arrange inspection of the group seal.
SUCCESS CHECK

The group remains dry around the portafilter throughout a normal shot.

10Steam wand is weak or sputteringmaintenance+

Steam pressure is low, inconsistent or mostly water.

LIKELY CAUSES
  • Machine has not reached steam temperature
  • Tip holes are blocked with dried milk
  • Wand was not purged
  • Scale is restricting steam performance
SAFE CHECKS · IN ORDER
  1. Let the complete steam-ready sequence finish.
  2. Purge briefly into the drip tray before and after milk use.
  3. When cool, wipe the wand and clear only the removable tip as the manual directs.
  4. Never insert unapproved objects deeply into the wand.
  5. Run the prompted cleaning or descale program if due.
SUCCESS CHECK

Dry, steady steam exits all tip holes and remains consistent through a normal milk jug.

STILL NOT FIXED?

Use the exact manual or authorised support.

Record the model, serial number, warning message or light pattern, what happened immediately before the fault and the checks already completed.

Visit official Breville support ↗